The vi editor is available most of the Unix systems. vi can be used from any type of terminal because it does not depend on arrow keys and function keys--it uses the standard alphabetic keys for commands. vi is short form for "vi"sual editor. It displays a window into the file being edited that shows 24 lines of text. vi lets you add, change, and delete text, but does not provide such formatting capabilities as centering lines or indenting paragraphs. vi has many other commands and options not described here. You cannot remember all the commands until or unless you try out hands on with the commands.
You may use vi to open an already existing file by typing
vi your_file
where "your_file" is the name of the existing file. If the file is not in your current directory, you must use the full pathname.
Or you may create a new file by typing
vi new_file
where "new_file" is the name you wish to give the new file.
On-screen, you will see blank lines, each with a tilde (~) at the left, and a line at the bottom giving the name and status of the new file:
~
"new_file" [New file]
vi has two modes:
- command mode
- insert mode
In command mode, the letters of the keyboard perform editing functions (like moving the cursor, deleting text, etc.). To enter command mode, press the escape <Esc> key.
In insert mode, the letters you type form words and sentences. vi starts up in command mode.
In order to begin entering text in this empty file, you must change from command mode to insert mode. To do this, type
i
Nothing appears to change, but you are now in insert mode and can begin typing text. In general, vi's commands do not display on the screen and do not require the Return key to be pressed.
Type a few short lines and press <Return> at the end of each line. If you type a long line, you will notice the vi does not word wrap, it merely breaks the line unceremoniously at the edge of the screen.
If you make a mistake, pressing <Backspace> or <Delete> may remove the error, depending on your terminal type.
To delete a character from a file, move the cursor until it is on the incorrect letter, then type
x
The character under the cursor disappears. To remove four characters (the one under the cursor and the next three) type
4x
To delete the character before the cursor, type
X (uppercase)
To delete a word, move the cursor to the first letter of the word, and type
dw
This command deletes the word and the space following it.
To delete three words type
3dw
To delete from the cursor position to the end of the line, type
D (uppercase)
To delete a whole line, type
dd
The cursor does not have to be at the beginning of the line. Typing dd deletes the entire line containing the cursor and places the cursor at the start of the next line. To delete two lines, type
2dd
To replace one character with another:
- Move the cursor to the character to be replaced.
- Type letter r
- Type the replacement character.
The new character will appear, and you will still be in command mode.
To replace one word with another, move to the start of the incorrect word and type
cw
The last letter of the word to be replaced will turn into a $. You are now in insert mode and may type the replacement. The new text does not need to be the same length as the original. Press <Esc> to get back to command mode. To replace three words, type
3cw
To change text from the cursor position to the end of the line:
- Type C (uppercase).
- Type the replacement text.
- Press <Esc>.
To add text to the end of a line:
- Position the cursor on the last letter of the line.
- Type a
- Enter the new text.
We use this very often insert text is more oftenly used than this
To insert a blank line below the current line, type
o (lowercase)
To insert a blank line above the current line, type
O (uppercase)
To join two lines together:
- Put the cursor on the first line to be joined.
- Type J
To join three lines together:
- Put the cursor on the first line to be joined.
- Type 3J
Undo (Ctrl + Z)
To undo your most recent edit, type
u
To undo all the edits on a single line, type
U (uppercase)
Note: Undoing all edits on a single line only works as long as the cursor stays on that line. Once you move the cursor off a line, you cannot use U to restore the line.
To move the cursor to another position, you must be in command mode. If you have just finished typing text, you are still in insert mode. Go back to command mode by pressing <Esc>. If you are not sure which mode you are in, press <Esc> once or twice until you hear a beep. When you hear the beep, you are in command mode.
There are shortcuts to move more quickly though a file. All these work in command mode.
Key description
--- --------
h left one space
j down one line
k up one line
l right one space
w forward word by word
b backward word by word
$ to end of line
0 (zero) to beginning of line
H to top line of screen
M to middle line of screen
L to last line of screen
G to last line of file
1G to first line of file
<Control>f scroll forward one screen
<Control>b scroll backward one screen
<Control>d scroll down one-half screen
<Control>u scroll up one-half screen
To move quickly by searching for text, while in command mode:
- Type / (slash).
- Enter the text to search for.
- Press <Return>.
The cursor moves to the first occurrence of that text.
To repeat the search in a forward direction, type
n
To repeat the search in a backward direction, type
N
To move to a specific line nuber u can type
:
To save the edits you have made, but leave vi running and your file open:
- Press <Esc>.
- Type :w
- Press <Return>.
CLOSE FILE
To close vi, and discard any changes your have made since last saving:
- Press <Esc>.
- Type :q!
No comments:
Post a Comment